May we count your visit with Google Analytics? It uses cookies and sends visit data to Google. You can change this any time under Cookie choices. Privacy
Plug in a panel whose connector matches the station's solar input, or use the maker's adapter cable, and keep the
panels' open-circuit voltage under the input's top voltage on the coldest morning you expect. Then stop adding panels at
the input's watt limit: beyond it, extra panels charge no faster in full sun. A station refills in its capacity divided by the
watts coming in, so a 1,000 Wh station on 200 W takes at least 5 hours of full sun from empty.
From each maker's published input limits and panel figures, with our own arithmetic; we have not tested these setups ourselves.
Your station, worked
Example: the Jackery Explorer 1000 v2, one of the most-searched stations. Pick your own.
The Jackery Explorer 1000 v2 takes up to 400 W of solar into its 1,070 Wh battery.
Quickest refill from a maker panel: 2 × EcoFlow 400W, 1 panel on each of its 2 solar inputs, about 2.7 h of full sun from empty (the same at a 70% panel yield: the panels are big enough to hold the limit even then). Cable: an MC4-to-DC8020 solar cable.
Lowest panel cost at the full input: 2 × BLUETTI PV200, 1 panel on each of its 2 solar inputs, about 3.8 h at a 70% yield.
Read the solar input's limits. The manual or spec table gives a voltage range (for example 12 to 60 V),
a current (in amps) and a watt limit. The voltage range is the one that matters most: below its bottom the station does not
start charging, and above its top it can be damaged. Our setup page for each station quotes the
maker's own lines.
Choose the panel watts. Aim at the input's watt limit, or a little above it so the input stays full for
more of the day: panels give about 70% of their rating on a good day, which is the yield we plan with. Watts above the limit are
wasted at midday. On 91 of the 118 stations we have setups for, the quickest setup uses more than one panel.
Wire the panels for the input. Panels in series add their voltages; strings in parallel add their
currents. Series suits a high-voltage input, parallel a low-voltage one with a higher current limit. Two panels that each
fit can break a limit together, so check the whole array, not one panel.
Check the coldest morning. A panel's open-circuit voltage (Voc) is printed for 25 °C and rises as it gets colder, by about
0.25% to 0.35% per °C. EcoFlow's 400 W panel is rated 48 V open-circuit and reaches about 53.5 V on a
-10 °C (14 °F) morning; two in series reach 107 V, too much for a 60 V input. Across our setups, the cold check
lowers or rules out 320 station-and-panel pairs that would pass on a mild day.
Use the right cable. Panels end in MC4 plugs or their maker's own (Jackery's DC8020 or Anderson). Most
stations take XT60 or XT60i; others take DC8020 (8 mm), XT90, Anderson, DC5521 or MC4. On 108 of the 118 stations, the quickest maker panel needs an adapter cable, and on 87 it comes
from another maker than the station's.
Place the panels. Face them square to the sun: in the US, toward the south, tilted up at about your
latitude (steeper in winter, flatter in summer). A panel on its kickstand catches more if you turn it to follow the sun
every two or three hours. Keep every cell out of shade: in a series string the same current runs through every panel, so a
shadow across one cuts the whole string. Leave the station itself in the shade, since a hot station slows or stops charging.
Plug in and check the input watts. Read the solar watts on the station's display or app. If it shows
nothing, see why a station may not charge below.
Series and parallel, drawn from real setups
Each picture is a setup from our pages, drawn as it is wired. The setups use identical panels, which is what makers advise.
Series: voltages add2 × EcoFlow 110W on the Aferiy P010: 2 in series on the solar input; 200 W in.
Two panels in one string, for the Aferiy P010: twice the voltage, the current of one panel.
Parallel: currents add2 × EcoFlow 400W on the Aferiy P180: 2 in parallel on the solar input; 500 W in.
Two strings side by side, for the Aferiy P180: the voltage of one panel, twice the current, joined by an MC4 branch connector.
How long it takes
Hours of full sun to refill = the station's watt-hours ÷ the watts coming in. The watts coming in are the lower of the panels'
output and the input's limit. At the limit that is the fastest the station can refill; at a 70% panel yield it takes
longer. A usable day holds four to six hours of full sun in most of the US. In December a panel tilted for winter gets about
2.5 in Chicago and 5.3 in Phoenix, by NASA's averages (solar panels in winter). So a refill from empty can take more than one day, and a station that powers a fridge needs
enough panel watts to put back what the fridge uses each day; each setup page works that out.
Why a station may not charge from solar
Too little voltage. One small panel on an input that starts at 30 V or more, or shade and low sun, can keep the panels below the input's lowest voltage.
Too much voltage. Above the input's top voltage the station protects itself and stops, or is damaged. Recheck series strings in the cold.
Too cold or too hot to charge. Most makers rate charging only from 0 °C (32 °F) upward; the manual gives the station's own range.
A loose plug. An MC4 joint not clicked home, or an adapter cable made for another station's input.
Questions buyers ask
Do I need a separate charge controller?
No, for the stations we list: each has a solar charge controller built in, which takes what the panels give up to the input's limits. Plug the panels into the input the maker names for solar.
Can I use another brand's panels?
Yes, when the voltage, current and watts stay inside the input's limits and you have the cable for the plugs. On 87 of the 118 stations we have setups for, the quickest maker panel on sale is another brand's. Some makers advise against mixing their panels with other brands or types in one array.
Can I mix different panels in one array?
It is best not to. In series, the panel with the lowest current holds back the string; in parallel, the strings settle at the lower voltage. Our setups use identical panels for that reason.
Is a bigger panel always faster?
Only up to the input's watt limit. A 400 W panel on a 200 W input charges at 200 W at most; it helps only by holding the limit for more of the day, at a higher price and weight.